Niamh Cullen tech

  1. Workshop dress:
    Name 4 things you should make sure of when dressing for workshop work?
    • 1. Don't let SLEEVES, ties, hair etc hang loose
    • 2. Wear protective GOGGLES
    • 3. Wear protective SHOES
    • 4. Wear protective GLOVES
  2. Workshop dress:
    When working with acids, what should you ensure?
    You're wearing GOGGLES to protect your eyes.
  3. Workshop - preparation:
    Name 4 things you should check before you BEGIN operating a machine?
    • 1. ensure that your work is in a VICE
    • 2. ensure that machine GUARDS are properly in place
    • 3. ensure that cutting tools are SHARP and are set correctly
    • 3. ensure you know where the STOP button is
  4. Workshop - when operating the machine, you should (3):
    • 1. keep your hands away from MOVING PARTS
    • 2. ensure GOGGLES are covering your eyes
    • 3. keep your hands away from the CUTTIN EDGE
  5. Workshop behaviour:
    Name 3 correct behaviours when in a workshop?
    • 1. never RUN
    • 2. get PERMISSION to use a machine
    • 3. if you have any DOUBTS, ask teacher
  6. Workshop - working with resins:
    What should you make sure of before working with resins?
    Ensure that you are wearing GLOVES or BARRIER CREAM.
  7. Tools and Equipment:
    What's this and what is it used for?
    Image Upload 2
    It's a FRET SAW.I

    It's used for cutting out intricate shapes and patterns and has a very thin blade.
  8. Tools and Equipment:
    What is this called and what is it used for?
    Image Upload 4
    A HEGNERSAW or SCROLL SAW.

    It's a motorised version of the Fret Saw. It's used for cutting intricate shapes in wood and can cut wood up to 25mm thick. It is a very dangerous machine to use!
  9. Tools and Equipment:
    What is this called and what is it used for?
    Image Upload 6
    A BANDFACER.

    It's used for sanding (smoothing) wood surfaces.
  10. Tools and Equipment:
    What is this called?
    Image Upload 8
    A VICE, or vice-grip.

    It's used for holding things tightly in place.
  11. Tools and Equipment:
    What is a cramp and what's it used for?
    It's a G shaped device used for tightening two pieces of wood together to make the glue set properly.
  12. Nails:
    What are they normally made from? Name 3 types and say what they're used for.
    • Nails are normally made form mild steel.
    • Three types:
    • ROUND WIRE - for cheap constuction work
    • OVAL WIRE - for better quality work
    • PANEL PIN - for fixing thin sheet material
  13. Nails:
    What's the main difference between Round Wire nails and Oval Wire nails?
    The heads in Oval nails can be hammered in below the surface, whereas the heads of Roundwire nails cannot.
  14. Nails:
    What is a nail punch used for?
    To punch nails in below the surface.
  15. Glues:
    What does PVA stand for?
    Poly vinyl acetate.

    It's a white creamy glue and is the most commonly used type of glue.
  16. Glues:
    When using PVA to glue joints together, why do you need to wipe off excess glue with a paper towel?
    Because it's very difficult to remove once it's set (after about 4 hours).
  17. Glues:
    What are the two types of PVA?
    Waterproof and non-waterproof PVA
  18. Glues and nails:
    What's the process for joining two pieces of wood together using glue and nails?
    • 1. hold one piece securely in a vice
    • 2. get the nails started in the other piece of wood
    • 3. put a THIN LAYER of glue on both touching surfaces
    • 4. position and hammer in the nails
    • 5. wipe off any excess glue
  19. Woods:
    Name the three types and state where they come from.
    • Hardwood - comes from broad-leaf decidious trees eg OAK, ELM
    • Softwood - comes from conifer trees.
    • Manufactured - from factories!
  20. Woods:
    Name the four types of manufactured board.
    • plywood
    • blockboard
    • chipboard
    • hardboard
  21. Woods:
    What is plywood and what is it used for?
    Plywood is made by sticking "veneers" together.

    It's used for toys and the bottoms of drawers.
  22. Woods:
    How is blockboard made and what is it used for?
    Blockboard is made by sticking many thin layers of softwood side by side, then sticking a thin veneer on each side.

    It is used for making modern furniture.
  23. Woods:
    How is chipboard made and what is it used for?
    Chipboard is made by gluing thousands of tiny bits of wood.

    It is used with a front veneer for kitchen cupboards.
  24. Woods:
    What is hardboard and what is it used for?
    Hardboard is made by gluing and compressing pulped wood.

    It is used for large areas like the backs of cupboards.
  25. Woods:
    Name two types of hardwood and give example of uses.
    • Mahogany hardwood - used for high quality furniture
    • Beech hardwood - used for workbenches.
  26. Woods:
    Name two types of softwood and give example of their uses.
    • Redwood - honey colour - house roofs and window frames
    • Parana pine - pale yellow - staircases.
  27. Woods:
    What is the purpose of seasoning wood?
    To clear out water from the tree.
  28. Woods:
    How is the age of a tree found?
    By counting it's annual rings.
  29. Electronics - Circuits:
    What does it mean if two lights are "in series"?
    How does the current going through them compare to the current being supplied by the battery?
    • It means that they are one after each other in a straight line.
    • The current going through both is the same as the current being supplied by the battery.
  30. Electronics - Circuits:
    What does it mean if two lights are "in parallel" in a circuit? If there were three lights in parallel, how would the current going through each compare to the current being supplied by the battery?
    In parallel means that they appear in a parallel in a circuit.

    If three lights were in parallel, the current going though them would be 1/3rd of the current being supplied by the battery.
  31. Electronics - Circuits:
    Are the lights in series or in parallel?
    Image Upload 10
    In series (current is the same throughout).
  32. Electronics - Circuits:
    Are the lights in series or in parallel?
    Image Upload 12
    • In parallel.
    • Here, the current from the battery gets split into three. Each of the lights gets the same current through it, but this current is only 1/3rd of the current a bulb in a series circuit would get.
  33. Electronics - Switches:
    Draw the symbol for a "push to make" switch and describe what it does.
    • Image Upload 14
    • It MAKES the circuit when pressed down.
  34. Electronics - Switches:
    Draw the symbol for a "push to break" switch and describe what it does.
    • Image Upload 16
    • when pushed it BREAKS the circuit
  35. Electronics - Switches:
    Draw the symbol for a "reed" switch and describe what it does.
    • Image Upload 18
    • when a magnet comes near, the reed wires are forced together to make the circuit.
  36. Electronics - Switches:
    Draw the symbol for a "On/off" switch and give another name for it.
    • Image Upload 20
    • another name is : SPST switch
    • (single pole, single throw)
  37. Electronics - Switches:
    Draw the symbol for a "2 way" switch and give another name for it.
    Image Upload 22

    • another name is SPDT switch.
    • (single pole, double throw)
  38. Electronics - LEDs:
    What does LED stand for?
    Light Emitting Diode
  39. Electronics - LEDs:
    When including an LED in any circuit, what must you remember to include, and why?
    To put a resistor in front of it in the circuit. This is because LEDs only need a tiny amount of current (max 30mA) and the resistor will dramatically reduce the current going into the LED so it doesn't burn out. LEDs typically operate between 10-20mA of current.
  40. Electronics - LEDs:
    What are the two legs of an LED called and which one is postive / negative?
    • Anode - negative (think of anti)
    • Cathode - positive (this leg is longer than the anode)
  41. Electronics - LEDs:
    What is the safe operating voltage of an LED?
    1.5 volts up to 5 volts
  42. Electronics - LEDs:
    What way should a LED be connected to a battery (postive / negative)?
    The negative ANODE should be connected to the POSTIVE BATTERY terminal.

    The positive CATHODE should be connected to the NEGATIVE BATTERY terminal.
  43. Electronic - Circuit Calculations:
    What is the formula relating voltage, current and resistance? What are the units of each?
    • V = I . R
    • V is voltage and is in VOLTS
    • I is current and is in AMPS
    • R is resistance and is in OHMS
  44. Electronic - Circuit Calculation:
    If a circuit has a 9V battery and the resistor is 200ohms, will the LED work ok (show why)?
    No the LED will burn out, because the current going though it will be too high.

    • Using V = I.R
    • I (current) would be 9/200 = 0.045A = 45mA. Most LEDs will burn out at above 30mA.
Author
Anonymous
ID
58379
Card Set
Niamh Cullen tech
Description
Niamh's Y8 christmas test
Updated