MG82

XTL 5000 HIGH power requirements

XTL 5000 LOW power requirements

XTL 5000 IFR test: Speak into microphone in a clear loud voice giving a ten count and deviation is 1kHz; what do you do?

What branch does not have CWO?

What is the form number for antenna resistance checks?

Port 2 on 29' MFD?

Number of tag-out logs kept on cutters?

Safety observer must remain within what distance of the climber?

What are the 2 types of weather proofing sleeves?

What type of equipment is GIMCP not used for?

What type of equipment is GIMCP not used for?

Year all ratings opened for women?

How long do you keep Tag-Out logs?

CO can give permission to whom to remove Danger Tags?

How many volts for "danger high voltage" sign?

Let-go current?

Electronic equipment owned and managed by the ELC

What is the life expectancy of the 2-2-1 weatherproofing method?

Coast Guard classifies VHF frequency

Shorting probe voltage rating?

Rubber gloves voltage rating?

Rubber floor matting rating?

2x PEL limit

3x PEL limit

How do you reinstall transducer bolts?

Who cannot you not get underway without?

What cutter rammed a submarine?

When does a member receive a special set of marks?

Weatherproofing temp range?

Tool control is managed by who?

What CASREP category does the CG not use?

What does a 96 code on a piece of test equipment mean?

Never use vulcanizing tape below what temp?

The MRC Codes:
D
W
M
Q
S
A
C
R

When a single maintenance requirement
has need for more than one penodicity they will be numbered as “Q-lR”, “M-lR”, “M-2 R”, etc.; the “R;’ in the case meaning “______,” indicates a situation that is defined in an accompanying note.

In cases where classification

of an individual MRC is required due to content, the following entry is found in the “Procedure” block: “Maintenance Procedure with this requirement is CLASSIFIED. _________"

The completed MRC Quarterly Schedule shall be signed by the __________ in the
“____________” block.

At the end of each work week, the Work Center Supervisor will _________ all maintenance requirements on the MRC Quarterly Schedule that have been completed and will _______  afl requirements that were not accomplished.

The _______________ is responsible for the rescheduling of all circled requirements on the MRC Schedule.

Any MRC requirement which cannot be accomplished during the current quarter, in addition to being circled, shall be identified on the back of the _________ with the reason it was not accomplished.

The completed Quarterly Schedule is removed from the holder after the
close of each ________ and retained as a Planned Maintenance record. This record may be discarded by ______, when the same number ______ after the next major overhaul has been completed, thereby providing a complete cycle of history.

The Weekly Schedule (____________), is a visual display of planned maintenance scheduled for accomplishment in a given Work Center during that week.

The _____________________ provides a means for recording the expenditure
of resources (men, material and time)
associated with certain categories of maintenance

actions.

This information is also retrievable for use in maintenance problem and logistic support analysis and for developing a Current
_______________ file which will assist
in improving the planning and coordination of the ship’s workload.

Using a Work Supplement  Card to document the delay code __ will be used to show the delay status from that work center WPL & C reports.

Multiple Units. Multiple Unit work
requests on items such as binoculars, printing, photographing, plaques, sound-powered phones, clocks, etc., are permitted by using the words “______” or “______” in block 9 of the work request submitted on
a 4790/2K form. Block 9 of the pre-punched 4790/2F card will always be blank when associated with this type work request. These multiple items will always be documented as a single maintenance action unless rejection of individually serialized items is involved.

What is a good reading for a CEMT 390 HF antenna?

Completion of a work request can be reported using the 4790/2F and entering
the code’’__” in block G.

The FSN is generally found in the ______________ within the Allowance
Parts List/Allowance Equipage List (APL/AEL) for the equipment/component being worked on. When only the part number is known, the NSN may be obtained from the ________________.

When an item is identified only by the Manufacturer’s Part Number for which no NSN has been assigned, the part number preceded by the _______________ will be entered.