Home
Flashcards
Preview
API 510 Data Sheets Misc - CLOSED BOOK QUESTIONS
Home
Get App
Take Quiz
Create
Automatically remove your image background. Try it now!
https://remove-image-background.com
Define repair (key words)
Restore and suitable
Reference API 510: 3.1.61
Define alteration (key words)
Physical change
Reference API 510: 3.1.1
Define RBIs two primary factors
Probability and consequence
Reference API 510: 5.2.1
Where is the MAWP located at on a vessel?
The top.
Reference API 510: 3.1.44
What is an imperfection that exceeds the acceptance criteria?
A defect.
Reference API 510: 3.1.15
What is a flaw that may or may not exceed the acceptance criteria?
An imperfection
Reference API 510: 3.1.27
Design - What is the joint category of a vessel longitudinal weld?
A
Reference VIII: Fig UW-3
Design - What is the joint category of a vessel circumferential weld?
B
Reference VIII: Fig UW-3
What is the joint category of a vessel nozzle attachment weld?
D
Reference VIII: Fig UW-3
What is the joint category of a vessel flange-to-nozzle attachment weld/shell-to-girth flange attachment weld?
C
Reference VIII: Fig UW-3
Design - What are the RT factors representing full RT?
RT-1 and RT-2
Reference VIII: UG-116.e.1 and 2
Design - What are the RT factors representing Spot RT?
RT-3
Reference VIII: UG-116.e.3
Design - Weld Type - Butt double welded?
Type 1
Reference VIII: Figure UW-12
Design - Weld Type - Butt single welded with backing?
Type 2
Reference VIII: Figure UW-12
Design - Weld Type - Butt single welded without backing?
Type 3
Reference VIII: Figure UW-12
Design - What vessel service always requires full RT?
Lethal
Reference VIII: UW-11.a.1
Design - What is the maximum set pressure for a single relief device on a vessel?
MAWP
Reference VIII: UG-134.a
Design - What is the marking on the nameplate that indicates the vessel was PWHT'D?
HT
Reference VIII: UG-116.f.1
Design - What is the marking on the nameplate that indicates the vessel is in lethal service?
L
Reference VIII: UG-116.c
Design - What is the ASME Sect VIII stamp for routine vessels?
U
Reference VIII: UG-116.a.1.a
Design - What is the ASME Sect VIII stamp for miniature vessels?
UM
Reference VIII: UG-116.a.1.b
Design - What is the ASME Sect VIII stamp for relief devices?
UV
Reference VIII: UG-129.a.7
NDE - What is the number of CMLs required to obtain thickness readings during inspection? (key word)
Representative
Reference API 510: 5.6.2.1
NDE - What is the number of nozzles to obtain thickness readings on during inspection? (Key word)
Representative
Reference API 510: 5.6.2.1
NDE - What lead letter is used during RT to check for backscatter radiation?
B
Reference Sect V: T-223
NDE - What lead letter is used during RT to indicate a film-side IQI?
F
Reference Sect V: T277.b
NDE - What hole size must be visible during RT when using a hole-type IQI?
2T
Reference Sect V: Table T-276
NDE - What are the type primary gamma-ray RT sources?
Ir 192 and Co 60.
Reference API 577: 9.8.4
Relief Valves - How are relief devices to be transported?
Upright
Reference API 576: 5.8.4.2
Relief Valves - How are relief device intervals determined? (key word)
By performance
Reference API 510: 6.6.3.1
Welding - What are the variables needed on a WPS?
Essential and Non-essential
Reference IX: QW200.1.b
Welding - Variables needed on a PQR?
Essential
Reference IX: QW200.2.b
Welding - What welding processes are used when substituting preheat or CDW (controlled deposition welding) for a required PWHT? (3)
SMAW, GMAW, GTAW
Reference API 510: 8.1.7.4.3.2.1.b and 8.1.7.4.3.3.c
Welding - What is the minimum taper required for shell welds with mismatch?
3 to 1
Reference VIII: UW 9.c
Weld Qualification - What is the "all position" test coupon?
6G
Reference IX: QW461.9
Weld Qualification - What indications are rejectable in RT when qualifying a welder?
Cracks, Incomplete penetration, and Lack of fusion
Reference IX: QW191.1.2.2.a.1
Weld Qualification - Which welding process can a welder NOT be qualified by RT?
GMAW - SC
Reference IX: QW-304
Weld Qualification - What is the maximum allowed thickness on a WPS based on the plate thickness (T) of PQR test coupon?
2T
Reference IX: Table QW451.1
Automatically remove your image background. Try it now!
https://remove-image-background.com
Author
Gibby
ID
333652
Card Set
API 510 Data Sheets Misc - CLOSED BOOK QUESTIONS
Description
MSTS Misc
Updated
2017-08-23T02:09:23Z
Show Answers
Home
Flashcards
Preview