Pipefitting Hand tools

The flashcards below were created by user JOMC0092800 on FreezingBlue Flashcards.

  1. A screwdriver may be used as a pry bar as long as it is sturdy enough for the application. 

    a) True
    b) False
    b) False
  2. A three-legged pipe jack stand can be used for pipe up to _____ inches in diameter. 

    A) 4
    B) 6
    C) 2
    D) 8
    B) 6
    (this multiple choice question has been scrambled)
  3. The height of a three legged jack stand is typically adjusted by placing it on blocks.

    a) True 
    b) False
    b) False
  4. The type of wrench that would be used on a chrome plated pipe is the ______ wrench.

    A) Crescent
    B) offset pipe
    C) chain
    D) strap
    D) strap
    (this multiple choice question has been scrambled)
  5. Image Upload 1

    The tool shown in Figure 1 is a(n)________. 

    A) offset pipe wrench
    B) pipe vise
    C) compound leverage pipe wrench
    D) strap wrench
    C) compound leverage pipe wrench
    (this multiple choice question has been scrambled)
  6. The term plumb relates to _______.

    A) horizontal alignment
    B) pipe location
    C) vertical alignment
    D) pipe height
    C) vertical alignment
    (this multiple choice question has been scrambled)
  7. A torpedo level is a good choice when accuracy is important

    a) True
    b) False
    b) False
  8. A framing level can be used to measure ______. 

    A) plumb or level 
    B) level only
    C) boobies :)
    D) plumb only
    A) plumb or level
    (this multiple choice question has been scrambled)
  9. Which of the following is a task that cannot be performed with a framing square?

    A) Finding the center line of a pipe
    B) Aligning two sections of pipe
    C) Checking squareness of a pipe end
    D) measuring the diameter of a pipe
    D) measuring the diameter of a pipe
    (this multiple choice question has been scrambled)
  10. Image Upload 2

    Figure 2 shows a tool used to _____.

    A) bevel a pipe
    B) measure the outside diameter of a pipe
    C) tap a hole in a pipe 
    D) locate the center of a pipe
    D) locate the center of a pipe
    (this multiple choice question has been scrambled)
  11. A t-joint welding clamp is used to hold a pipe section perpendicular to another pipe.

    a) True 
    b) False
    a) True
  12. A Hi-Lo gauge is used to ______.

    A) check pressure in a piping system
    B) check pipe joint misalignment
    C) check for weld defects
    D) measure the inside diameter of a pipe
    B) check pipe joint misalignment
    (this multiple choice question has been scrambled)
  13. A wraparound is used to ______.

    A) secure a pipe to a jack stand
    B) measure the inside diameter of a pipe
    C) draw a straight line around a pipe 
    D) align pipe joints for welding
    C) draw a straight line around a pipe
    (this multiple choice question has been scrambled)
  14. Drift pins are used to _____.

    A) align bolt holes on pipe flanges
    B) check alignment of a pipe joint
    C) secure pipes in jack stands
    D) keep pipe joints from moving while they are being welded
    A) align bolt holes on pipe flanges
    (this multiple choice question has been scrambled)
  15. A hacksaw blade used to cut copper tubing should have ______ teeth per inch.

    A) 14
    B) 32
    C) 24
    D) 18
    C) 24
    (this multiple choice question has been scrambled)
  16. Image Upload 3

    The tool shown in Figure 3 is used to cut _____.

    A) cement pipe
    B) cast iron soil pipe
    C) carbon steel pipe
    D) thin-wall copper tubing
    C) carbon steel pipe
    (this multiple choice question has been scrambled)
  17. Image Upload 4

    The tool shown in Figure 4 is used to _____.

    A) thread pipe 
    B) ream pipe
    C) bevel pipe ends
    D) position pipe for welding
    A) thread pipe
    (this multiple choice question has been scrambled)
  18. Threading is complete when ____ full thread (s) extend(s) beyond the back edge of the die.

    A) 2
    B) 3
    C) 1
    D) 4
    C) 1
    (this multiple choice question has been scrambled)
  19. Pipe taps are used to _____.

    A) cut male threads of a pipe
    B) cut female threads of a pipe
    C) remove broken plugs and fittings
    D) drill holes in pipe
    B) cut female threads of a pipe
    (this multiple choice question has been scrambled)
  20. Lever compression tube benders can be used to bend pipe up to 1 inch in diameter.

    a) True
    b) False
    b) False
  21. What is Burr?
    Burr is a sharp, tagged edge of metal usually caused by cutting pipe.
  22. What is Conduit?
    Conduit is a round raceway, similar to pipe, that contains conductors.
  23. What is die?
    Die is a tool used to make male threads on a pipe or bolt.
  24. What is female threads?
    Female threads are threads on the inside of a fitting
  25. What is Flare?
    Flare is a pipe end that has been forced open to make a joint with a fitting
  26. What is male threads?
    Male threads are threads on the outside of a pipe.
  27. What is the outside diameter?
    The outside diameter is a measurement of the outside width of a pipe.
  28. What is Pipe-fitting?
    Pipe-fitting is a unit attached to a pipe and used to change the direction of fluid flow, connect a branch line to a main line, close off the end of a line, or join two pipes of the same size or of different sizes.
  29. What is a Ratchet?
    A ratchet is a device that allows a tool to rotate in only one direction
  30. What is tack welds?
    Tack welds are short welds used to hold parts in place until the final weld is made.
  31. What is a thread gauge? What else can it be called?
    A tool used to determine how many threads per inch are cut in a tap, die, bolt, nut or pipe. Also called a pitch gauge.
Author
ID
304091
Card Set
Pipefitting Hand tools
Description
Pipefitting Level 1 Edition 3 Module 3
Updated
Show Answers