Network+ Ch3

Which UTP wiring uses four twisted wire pairs (eight wires) and is rated for 250MHz?

The point at which the operational control or ownership changes from your company to a service provider is referred to as ______.

Which type of cable will you use to connect switches?

Which RG rating of coax is used for cable modems?

Which UTP uses four twisted wire pairs (eight wires), is rated for 100MHz, and is capable of handling disturbance on each pair caused by transmitting on all four pairs at the same time?

You want to connect a host to a switch port.  What type of Ethernet cable will you use?

In what instance would you use T1 crossover cable?

568A uses which pins to make a connection?

568B uses which pins to make a connection?

What are two advantages of fiber-optic cabling?

What does EMI stand for?

What does RFI stand for?

Why would a network administrator use plenum-rated cable during an installation?

A. Low combustion temperature
B. High combustion temperature
C.  Reduces toxic gas released during a fire
D.  It is not susceptible to any intererence

Which of the following Ethernet Unshielded twisted-pair cabling types are commonly used?

A.  10BaseT
B.  100BaseTX
C.  1000BaseTX
D.  All of the above

In which of the following categories is UTP not rated?

A.  Category 2
B.  Category 5e
C.  Category 3
D.  Category 8

What type of connector does UTP cable typically use?

A.  SC
B.  ST
C.  RJ-45
D.  BNC

Which of the following provides the longest cable run distance?

A.  Multimode fiber
B.  Coax
C.  Category 3 UTP
D.  Single-mode fiber

You need to crimp on a connector using an RJ-45 connector.  Which pin-out configuration would you use to connect a host to a switch?

A.  UTP
B.  Crossover
C.  Rolled
D.  Straight-through

Fiber-optic cable is immune to electromagnetic interference (EMI) and radio frequency interference (RFI) because it ______.

A.  Transmits analog signals using light impulses
B.  Transmits digital signals using light impulses
C.  Transmits analog signals using electricity
D.  Transmits digital signals using electricity

What type of cable transmits lights from end to end?

A.  Coax
B.  UTP
C.  Category 2
D.  Fiber-optic

What is the main difference between single-mode fiber (SMF) and multimode fiber (MMF)?

A.  Single-mode can be run a shorter distance
B.  Number of digital signals
C.  Electrical signals
D.  Number of light rays

What type of cable should be used if you need to make a cable run longer than 100 meters?

A.  Fiber-optic
B.  Category 5e
C.  Category 6
D.  Coaxial

Which of the following are fiber-optic connectors?  Select three.

A.  LC
B.  RJ-11
C.  BNC
D.  ST
E.  SC
F.  RJ-45

You need to connect two devices on a vertical connect and they need to send voice traffic.  Which of the following cable will you use?

A.  Cat 5
B.  Cat 8
C.  Cat 3
D.  Rolled

How many hosts on a half-duplex segment can talk at one time?

A.  2
B.  1
C.  Unlimited
D.  0

Which type of cable does EMI have the least effect on?

A.  Coax
B.  UTP
C.  Fiber-optic
D.  STP

How many devices can be connected to a full-duplex segment?

A.  1
B.  0
C.  4
D.  2

How many wires are used in a 100 Mbps UTP transmission?

A.  2
B.  6
C.  4
D.  8

A crossover cable is used to connect all of the following except _____.

A.  Host to host
B.  Hub to switch
C.  Switch to switch
D.  Host to switch

How is a T1 crossover cable crosses wired?

A.  Pins 1, 2, 4, and 5 are connected to 3, 4, 5, and 6
B.  Pins 2, 3, 4, and 5 are connected to 4, 5, 1, and 2
C.  Pins 1, 2, 4, and 5 are connected to 4, 5, 1, and 2
D.  Pins 4, 5, 6, and 7 are connected to 4, 5, 1, and 2

The purpose of the demarcation point is to separate the customer from whom?

A.  The service provider
B.  Headquarters
C.  The branch office
D.  The data center

You need to make a 568B cable for a FastEthernet link.  How many pairs will you use?

A.  1
B.  4
C.  3
D.  2