CDC Volume 2 URE

An electrical charge at rest is called

Triboelectrification is the

In an ESD prtective area, what level of relative humidity is the most desirable

The electrostatic voltage sensitive threshold of the human body is approximately

when ESDS components are mounted on a circuit board, the

it is important for serviceable and un-serviceable (reparable) ESDS items to reveive the same ESD protection so

proper static drain is fast enough to quickly remove the static charge before any damage is done, yet slow enough so it doesn't produce a damaging

which is not one of the three principal components of a static control workstation

how often must a wrist strap be tested with a wrist strap tester

What is the proper procedure when you are testing a wrist strap with a wrist strap tester

you must torque a bolt to 60 inch-pounds, but you only have a foot-pound torque wrench. to what value must you set the foot-pound torque wrench to properly torque the bolt?

when would you use a torque wrench to break loose a bolt

Which torque wrench uses micrometers-like markings and a rotating adjustment sleeve to set torque values

You must compensate for the prevailing torque of a self-locking nut if its more than

you must compensate for the prevailing torque of a self-locking nut when the

before using a dropped torque wrench,you must

which is not provided by TAS

in the heterodyning or mixing process, what are the two new frequencies produced

which radio-frequency component is used to sample and input signal and does not have any moving parts

the radio-frequency component used to prevent any feedback in a circuit is the

the power meter

what control compensates for a slight sensitivity associated with a particular type of power sensor?

a power sensor is essentially a

before a power meter can be used, the meter and power sensor must be

when calibrating the power sensor, you adjust the CAL ADJ control so the digital readout indicates

before turning on the power meter, ensure it is

measuring relative power on a power meter is useful for

each division of the oscilloscope faceplate is

the horizontal divisions of an oscilloscope faceplate are calibrates to the settings of the

the VAR control of an oscilloscope must be in the calibrated detent or the time measurement will be

when measuring time on an oscilloscope, multiply the trace distance between reference points by the stetting of the

frequency is determined by the formula

a spectrum analyzer is simply a receiver with the output of

which control selects how much frequency band is represented by each division of a spectrum analyzer disply

Before using the spectrum analyzer to make any measurements, you must calibrate it using the

Which piece of test equipment is primarily used to self-calibrate devices within equipment and test stations

what does resolution mean in reference to a frequency counter

when using a pulse generator, selecting the NORM mode produces a

when using a pulse gernerator, the four control modes allow you to vary the output

when using the START FREQ function key on a sweep oscillator to select the start frequency for start/stop sweep operation, the start frequency must be at least 100 Hz lower than the

when using a sweep oscillator, the sweep time has an allowable range of

the 115 VAC, 400 Hz facility power input to a test station originates from the

what type of power supply is computer-controlled to produce variable outputs

the 400Hz facility power input to the test station is primarily used to

The 60 Hz facility power input to the test station is primarily used to

the concept of rousing, inciting, or increasing action refers to

which signal generator operates in the 20 Hz to 20 KHz frequency range

which signal generator operstes in the 1 GHz to 18 GHZ frequency range

what device is designed to measure AC voltage, DC voltage, and resistance?

providing a visual display for measuring voltage and frequency is a function of the

the concept of interconnecting UUT and test station recourses is

overall test station switching can be classed as

the most important test station function is

what numbering system is most widely used to allow computers to perform their functions?

Using IEEE-488 bus, devices can be linked in either linear, combination, or

what is the maximum total cable length specified for the IEEE-488 bus

At the maximum cable length specified for the IEEE-488 bus, how many devices can be connected?

what type of interface is the IEEE-488 bus

how many data lines does the IEEE-488 bus have

the end of identity line, which is part of the IEEE-488 bus/interface management lines, has two uses. The first part is to indicate end-of-date, and the second is to

each device on the IEEE-488 bus has a unique bus address that starts at 0 and goes up to

what device, usually a computer with an IEEE-488 board installed, always retains ultimate control of the bus

what process in the MIL-STD-1553B, transmits information from several sources through one system with different signals staggered in time to form a composite pule train?

up to how many units or terminals on an aircraft is the MIL-STD-1553B data bus designed to allow transfer of information between

referring to the MIL-STD-1553B bus architecture, how many buss controllers may be active on a 1553 multiplexed bus?

Which element that makes up the MIL-STD-1553B data bus system, is an avionics unit designed to transfer data between an aircraft component and the data bus?

the data bus in the MIL-STD-1553B data bus system is made up of two types of stubs, the transformer-coupled and

what is the only device that transmits a command word in the MIL-STD-1553B

refering to the MIL-STD-1553B data bus systems command, status, and data words, what is the only device that transmits a status word

referring to the VXI bus, there are two classification of devices with respect to register capabilities, on is register base and the other

which slot of the VXI chassis has special resources suck as backplane clocks, configuration signals, and synchronization signals

which size(s) of the VXI bus modules is/are the true VME bus module size(s)

Using the MXI bus, a computer can be located directly next to the VXI mainframe or up to how many meters away?

a computer or instrument with a MXI is called

the MXI bus has two cables, a point-to-point cable and a

a MXI bus system cansists of how many MXI bus devices connected in a daisy chain

what type of damage to the test station may result with improper usage of certain ATLAS system procedures

what is always the first section of an ATLAS program

what are the two basic fields that make up every ATLAS statement

what field of an ATLAS statement specifies in great detail exactly what is applied or how the timing of a signal is set up

what type of ATLAS statement does not require that use of the rest of the test station to properly execute

which type of nontest ATLAS statement alters the normal sequence of program flow?

which ATLAS test statement generate a signal that can have more states than just "on" or "off"

when calibrating ATE, you must consider

in a PATEC calibration, which error is not associated with a systematic error?

What organization sets national calibration standards

what calibration ratio is necessary to ensure sufficient traceability of standards

in PATEC equipment, what type of standard is a Rubidium frequency standard

the CAPRE uses what type of computer

the CAPRE is powered by a(n)