-
Where is the shimmy damper located?
In the tail wheel
-
What is the 1st thing you do to prepare for a DTA?
Check out MRC deck, PPE gear, review ADB
-
What MRC cards are used for the Daily & T/A?
300 & 100
-
What kind of Hydraulic fluid do we use on our A/C?
MIL-PRF-83282 (Football score)
-
What kind of oil is used for servicing the APU?
Mil-PRF- 23699 ( Jordan)
-
How long are the Daily & T/A's good for?
D-72 HR & T/A 24 Hr
-
How do we check the BIM indicators on the blades when doing a T/A?
Visual Inspection
-
What positon should the sonobouy launcher be in when sonobouies aren't installed?
Vent, lock & bottle lever in dump position.
-
When inspecting disconnect jaw seal what do you look for?
Gouges, nicks, deterioration & security.
-
What are the tire pressures?
75-85 & 95-105 psi
-
What pressure should the APU accumulator be serviced to?
2100-3100 psi
-
What pressure should the MRH Acmltr. be around?
1250-1500 psi depends on temperature
-
How many CADs are on a fire bottle?
2 each
-
Name the Press Differential Indicators (PDI's)
13 in all (1 wave guide 15 psi 700-800psi on bottles. 7 on engines, 1MGB, 6 hydraulic pumps & 1 pilot asist module)
-
What do you do if you get a bad fuel sample?
Keep the sample, drain a gallon, and take another sample, if its bad then notify QA or Maintenance
-
What PPE do we use when taking fuel samples?
Splash proof goggles, apron, face shield, gloves, Sleeves are down.
-
How long do you wait afer moving A/C to take fuel samples?
2 hours
-
How do we clean our fuel sample bottles?
Water and alchol (50/50) Alchanist..
-
What gear do we use when directing A/C at night?
Wands
-
Where is the torque shaft upper bearing locaed and what do you check it for?
Hyd. Bay. And checking for FOD, security, corrosion, proper lube.
-
Where is the blade fold detent, what does it do and what do you check for?
On Spindle, prevents lock pins from truning in fold position, cracks
-
Name the three main dampners on the A/C.
Viscous, Shimmy, Main Rotor Dampner
-
Name the three copper beryllium parts on the main rotor head?
Pitch lock housing, lock pin puller, droop stops.
-
Identify the bomb rack LEMA and IFOBL.
Linger Electromechanical Activator, and In Flight Operable Bomb Rack Lock
-
What type of bomb racks do the A/C have?
Bru - 14/A
-
Where is the Rast Cad and how do you tell if it's been fired?
Above the motor, and you can tell by the Cotter Pin.
-
Name all the Cads on the A/C.
4 on Fire Bottle, 3 Bomb Racks (2 each), Rescue Hoist, Rast, Mad Bird, Cargo Hook,
-
Approximately what pressure does hydraulic fluid flow through the lines?
3000 PSI
-
How fast do you tow an A/C?
5 mph or as fast as the slowest walker.
-
What is the only method authorized for shear wire?
Single strand
-
What do the words should and shall mean?
Should is a recommendation, and Shall ia a procedure..
-
What does it mean when there is a purple gel in the fuel sample?
The fuel cell self-sealing has been activated.
-
What items do you take with you for a hung MAD bird?
PRC_ 149 Radio, Grounding Sticks, Leather Gloves, Crainial
-
When is the only time that you raise the stab with battery power?
Never
-
What are the only mandatory hand signals?
Wave off, and Emergency Stop
-
What is the gas path cleaner to water ratio in the CC cart?
4 parts water to 1 part gas path cleaner
-
How many times do you rinse the engines on a water wash?
2 times
-
What parts of the daily cannot be done with the tail folded?
IGB/ TGB oil levels.
-
Where can you find a list of items to take on a cross-country flight?
Book in A/C and Duty Office
-
What does the word funny pertain to in the daily deck?
Viscous Dampners & Bearings with "Funny" odor.
-
What section of he A/C s washed daily, with soap and water when out at sea?
Center Bulkhead on Tail Cone and Tail Pylon
-
What is the max pressure for fueling and defueling?
Fueling is 55 psi and Defueling is 3 psi negative
-
How many feet in front and to the right when launching an A/C?
50ft foward of A/C and 10ft right of pilot
-
Does the PC sign the date on the "A" sheet?
No, Pilot signs when signing for A/C.
-
What is the OPNAV 4790/38?
Daily Paperwork
-
How many tiedown points are on the A/C?
6 (2 main mount, 2 tail, 2 High points)
-
What does a thermal runaway smell like?
Rotten Eggs
-
What is the rotor brake pressure?
450 - 690
-
What must be after servicing engines with oil?
Cap back on, Log in ADB & A-Sheet
-
What are the two types of rescue hoists?
Breeze Eastern / Lucas Western
-
How long must you wait between folding and spreading blads?
10 minutes
-
How long must you wait before moving an a/c after shutdown? Why?
20 minutes because of the Gyro's
-
What does corrosion look like on the MGB?
White Powder
-
What is the type MAF code for discrepancies found on dailies?
DF J & K when discovered code
-
What is the drag beam?
Beam from A/C float bag area to main landing gear.
-
How long mst you wait before handling the ALQ-144 TX?
30 minutes
-
What is a good indication on the BIM indicators?
All Black
-
What is the APU accumulator pressure?
2700-3100
-
Where is the MGB PDI?
Aft STBD side of bottom of MGB
-
The sonobouy launcher rotary valve must be in what position?
Vent & Lock
-
What circuit breaker must be pushed in prior to applying power to the A/C?
WOW
-
How many people are required to fold the tail?
5 (1 STAB 1Pin/Strat and 3 Pole)
-
How long does it take to complete a daily?
3 hours normally depending on the number of people
-
Are personnel allowed in the rotor arc with engines running and the blade not turning?
No
-
When shutting down the rotor blades, which stops first, the tail rotor or the main rotor?
Stop together
-
What should you do if the tail rotor starts windmilling when folding it?
Use a broom to slow it down.
-
How far back must you sand from the ESM antennas when radiating?
They dont radiate/ They're passive.
|
|