-
What will be the result of operating an engine in extremely high temperatures using a lubricant recommended by the manufacturer for a much lower temperature?
The oil pressure will be lower than the normal
-
(1) Gas turbine and reciprocating engine oils can be mixed or used interchangeably.(2) Most gas turbine engine oils are synthetic.Regarding the above statements,
only no. 2 is true.
-
An oil separator is generally associated with which of the following?
Engine-driven vacuum pump.
-
The time in seconds required for exactly 60 cubic centimeters of oil to flow through an accurately calibrated orifice at a specific temperature is recorded as a measurement of the oil's
Viscosity.
-
Upon what quality or characteristic of a lubricating oil is its viscosity index based?
Its rate of change in viscosity with temperature change.
-
Lubricating oils with high viscosity index ratings are oils
in which the viscosity does not vary much with temperature change.
-
Compared to reciprocating engine oils, the types of oils used in turbine engines
have less tendency to produce lacquer or coke.
-
The oil used in reciprocating engines has a relatively high viscosity due to
large clearances and high operating temperatures.
-
If all other requirements can be met, what type of oil should be used to achieve theoretically perfect engine lubrication?
The thinnest oil that will stay in place and maintain a reasonable film strength.
-
In addition to lubricating (reducing friction between moving parts), engine oil performs what functions?1. Cools.2. Seals.3. Cleans.4. Prevents corrosion.
1,2,3,4,5.
-
Which of these characteristics is desirable in turbine engine oil?
High flash point.
-
The viscosity of a liquid is a measure of its
resistance to flow.
-
What type of oil system is usually found on turbine engines?
Dry sump, pressure, and spray.
-
Which of the following factors helps determine the proper grade of oil to use in a particular engine?
Operating speeds of bearings.
-
Specific gravity is a comparison of the weight of a substance to the weight of an equal volume of
distilled water at a specific temperature.
-
Which of the following has the greatest effect on the viscosity of lubricating oil?
Temperature.
-
What advantage do mineral base lubricants have over vegetable oil base lubricants when used in aircraft engines?
Chemical stability.
-
The recommended aircraft engine lubricants are
mineral or synthetic based.
-
High tooth pressures and high rubbing velocities, such as occur with spur-type gears, require the use of
an EP lubricant.
-
Manufacturers normally require turbine engine oil servicing within a short time after engine shutdown primarily to
prevent overservicing.
-
What type of oil do most engine manufacturers recommend for new reciprocating engine break-in?
Straight mineral oil.
-
What type of oil do most engine manufacturers recommend after new reciprocating engine break-in?
Ashless-disperant oil.
-
The type of oil pumps most commonly used on turbine engines are classified as
positive displacement.
-
As a general rule, the mixture setting on a reciprocating engine operating at or near takeoff power that provides the best cooling is
FULL RICH.
-
The engine oil temperature regulator is usually located between which of the following on a dry sump reciprocating engine?
The scavenger pump outlet and the oil storange tank.
-
What will happen to the return oil if the oil line between the scavenger pump and the oil cooler separates?
The return oil will be pumped overboard.
-
At cruise RPM, some oil will flow through the relief valve of a gear-type engine oil pump. This is normal as the relief valve is set at a pressure which is
lower than the pressure pump capabilities.
-
(1) Fuel may be used to cool oil in gas turbine engines.(2) Ram air may be used to cool oil in gas turbine engines.Regarding the above statements,
both No. 1 and No. 2 are true.
-
In a reciprocating engine oil system, the temperature bulb senses oil temperature
at a point after the oil has passed through the oil cooler.
-
The oil dampened main bearing utilized in some turbine engines is used to
provide an oil film between the outer race and the bearing housing in order to reduce vibration tendencies in the rotor system, and to allow for slight misalignment.
-
What is the purpose of the last chance oil filters?
To filter the oil immediately before it enters the main bearings.
-
In a jet engine which uses a fuel-oil heat exchanger, the oil temperature is controlled by a thermostatic valve that regulates the flow of
oil through the heat exchanger.
-
What prevents pressure within the lubricating oil tank from rising above or falling below ambient pressure (reciprocating engine)?
Oil tank vent.
-
In an axial-flow turbine engine, compressor bleed air is sometimes used to aid in cooling the
turbine, vanes, blades, and bearings.
-
Oil picks up the most heat from which of the following turbine engine components?
Turbine bearing.
-
Which of the following is a function of the fuel-oil heat exchanger on a turbojet engine?
Increases fuel temperature.
-
According to Federal Aviation Regulations, oil tank fillers on turbine engines must be marked with the word
'oil.'
-
Oil tank fillers on reciprocating engines are marked with the word
"oil," in accordance with 14 CFR part 23.
-
After making a welded repair to a pressurized-type turbine engine oil tank, the tank should be pressure checked to
not less than 5 PSI plus maximum operating pressure of the tank.
-
Why are fixed orifice nozzles used in the lubrication system of gas turbine engines?
To provide a relatively constant oil flow to the main bearings at all engine speeds.
-
Possible failure related ferrous-metal particles in turbine engine oil cause an (electrical) indicating-type magnetic chip detector to indicate their presence by
Bridging the gap between the detector center (positive) electrode and the ground electrode.
-
What would be the probable result if the oil system pressure relief valve should stick in the open position on a turbine engine?
Insufficient lubrication.
-
What is the primary purpose of the oil-to-fuel heat exchanger?
Cool the oil.
-
What unit in an aircraft engine lubrication system is adjusted to maintain the desired system pressure?
Oil pressure relief valve.
-
Low oil pressure can be detrimental to the internal engine components. However, high oil pressure
Should be limited to the engine manufacturer's recommendations.
-
What is the primary purpose of the oil breather pressurization system that is used on turbine engines?
Provides a proper oil spray pattern from the main bearing oil jets.
-
The purpose of directing bleed air to the outer turbine case on some engines is to
Provide optimum turbine blade tip clearance by controlling thermal expansion.
-
Some larger reciprocating engines use a compensating oil pressure relief valve to
Provide a high engine oil pressure when the oil is cold and automatically lower the oil pressure when the oil warms up.
-
In order to relieve excessive pump pressure in an engine's internal oil system, most engines are equipped with a
relief valve.
-
What is the source of most of the heat that is absorbed by the lubricating oil in a reciprocating engine?
Pistons and cylinder walls.
-
How are the teeth of the gears in the accessory section of an engine normally lubricated?
By splashed or sprayed oil.
-
What is the purpose of the check valve generally used in a dry sump lubrication system?
To prevent the oil from the supply tank from seeping into the crankcase during inoperative periods.
-
From the following, identify the factor that has the least effect on the oil consumption of a specific engine.
Mechanical efficiency.
-
How is the oil collected by the piston oil ring returned to the crankcase?
Through holes drilled in the piston oil ring groove.
-
Which of the following lubrication system components is never located between the pressure pump and the engine pressure system?
Fuel line for oil dilution system.
-
As an aid to cold-weather starting, the oil dilution system thins the oil with
gasoline.
-
The basic oil pressure relief valve setting for a newly overhauled engine is made
in the overhaul shop.
-
Where is the oil temperature bulb located on a dry sump reciprocating engine?
Oil inlet line.
-
Cylinder walls are usually lubricated by
splashed or sprayed oil.
-
If a full-flow oil filter is used on an aircraft engine, and the filter becomes completely clogged, the
bypass valve will open and the oil pump will supply unfiltered oil to the engine.
-
Oil accumulation in the cylinders of an inverted in-line engine and in the lower cylinders of a radial engine is normally reduced or prevented by
extended cylinder skirts.
-
What is the primary purpose of changing aircraft engine lubricating oils at predetermined periods?
The oil becomes contaminated with moisture, acids, and finely divided suspended solid particles.
-
What determines the minimum particle size which will be excluded or filtered by a cuno-type (stacked disc, edge filtration) filter?
The spacer thickness.
-
What is the primary purpose of the hopper located in the oil supply tank of some dry sump engine installations?
To reduce the time to warm the oil to operating temperatures.
-
The purpose of the flow control valve in a reciprocating engine oil system is to
direct oil through or around the oil cooler.
-
Where are sludge chambers, when used in aircraft engine lubrication systems, usually located?
In the crankshaft throws.
-
Why is an aircraft reciprocating engine oil tank on a dry sump lubrication system equipped with a vent line?
To prevent pressure buildup in the oil tank.
-
Excessive oil is prevented from accumulating on the cylinder walls of a reciprocating engine by
oil control rings on the pistons.
-
(1) Wet sump oil systems are most commonly used in gas turbine engines.(2) In most turbine engine oil tanks, a slight pressurization of the tank is desired to ensure a positive flow of oil.Regarding the above statements,
only No. 2 is true.
-
The pumping capacity of the scavenger pump in a dry sump aircraft engine's lubrication system
is greater than the capacity of the oil supply pump.
-
In which of the following situations will the oil cooler automatic bypass valve be open the greatest amount?
Engine oil below normal operating temperature.
-
In order to maintain a constant oil pressure as the clearances between the moving parts of an engine increase through normal wear, the supply pump output
remains relatively constant (at a given RPM) with less oil being returned to the pump inlet by the relief valve.
-
The valve assemblies of opposed reciprocating engines are lubricated by means of a
pressure system.
-
What will result if an oil filter becomes completely blocked?
Oil will flow at the normal rate through the system.
-
A turbine engine dry sump lubrication system of the self-contained, high-pressure design
consists of pressure, breather, and scavenge subsystems.
-
Lube system last chance filters in turbine engines are usually cleaned
during overhaul.
-
How are the piston pins of most aircraft engines lubricated?
By oil which is sprayed or thrown by the master or connecting rods.
-
The vent line connecting the oil supply tank and the engine in some dry sump engine installations permits
the oil tank to be vented through the normal engine vent.
-
An engine lubrication system pressure relief valve is usually located between the
pump and the internal oil system.
-
Where is the oil of a dry sump reciprocating engine exposed to the temperature control valve sensing unit?
Oil cooler inlet.
-
Under which of the following conditions is the oil cooler flow control valve open on a reciprocating engine?
When the temperature of the oil returning from the engine is too low.
-
The purpose of a relief valve installed in the tank venting system of a turbine engine oil tank is to
prevent oil pump cavitation by maintaining a constant pressure on the oil pump inlet.
-
In a reciprocating engine, oil is directed from the pressure relief valve to the inlet side of the
pressure pump.
-
If the oil in the oil cooler core and annular jacket becomes congealed, what unit prevents damage to the cooler?
Surge protection valve.
-
The primary source of oil contamination in a normally operating reciprocating engine is
combustion deposits due to combustion chamber blow-by and oil migration on the cylinder walls.
-
A drop in oil pressure may be caused by
foreign material under the relief valve.
-
The main oil filters strain the oil at which point in the system?
Just as it leaves the pressure pump.
-
Which type valve prevents oil from entering the main accessory case when the engine is not running?
Check.
-
An oil tank having a capacity of 5 gallons must have an expansion space of
2 quarts.
-
As a general rule, a small amount of small fuzzy particles or gray metallic paste on a turbine engine magnetic chip detector
is considered to be the result of normal wear.
-
Why is expansion space required in an engine oil supply tank?
For oil enlargement and collection of foam.
-
The purpose of a dwell chamber in a turbine engine oil tank is to provide
separation of entrained air from scavenged oil.
-
Which of the following bearing types must be continuously lubricated by pressure oil?
Plain.
|
|
